When ordering replacement parts, include the complete identification number for all chassis, kits, and components. Therefore, it is important to order the correct antenna frequency split to match a specific customer frequency. Separation: Freq. Motorola Part No. And can be used as a Battery Eliminator.
Allows switching for radio testing. Motorola Model No. From this model number, you can determine the RF output power, frequency band, type of squelch, and number of channels. The table below outlines one portable radio model number and its specific characteristics.
Programming changes can be made by your local Motorola Radius dealer. Power Supply RA or equivalent. Plugs between the RIB and radio. Connect the RIB to the computer Figure 2. If your computer has an XT style communications port 25 pin connector , plug the HLN adapter into the computer and plug the HKN cable into the adapter. If you are unsure of which connection is on the back of your computer or the COM port, then please consult the computer manuals.
Connect the radio to a power supply and turn the volume control clockwise to turn it on. Throughout the text in this publication, you will notice the use of warnings, cautions, and notes. These notations are used to emphasize that safety hazards exist, and care must be taken and observed.
Motorola subscribes to the same safety standards for the use of its products. Proper operation of this radio will result in user exposure substantially below the FCC recommended limits. Do not hold the radio with the antenna very close to, or touching, exposed parts of the body, especially the face, ears, or eyes, while transmitting.
Hold the radio in a vertical position with the microphone two to three inches away from the lips. Under certain conditions, radios can interfere with blasting operations. When you are in the vicinity of construction work, look for, and observe, signs cautioning against radio transmission.
If radio transmission is prohibited, you must not transmit until out of the area. Furthermore, you must turn off your radio to prevent any accidental transmission. Contact sparking may occur while installing or removing batteries and cause an explosion. NOTE An operational procedure, practice, or condition, etc. Radios must ship from the Motorola manufacturing facility with the hazardous atmosphere capability and FM Approval labeling.
Modifications can only be done by the original product manufacturer at one of its FMRC audited manufacturing facilities. Their Approval mark is shown below. FMRC Approved for such use. An explosion or fire may result. You may want to consider using a repair facility that operates under repair service approval. Do not replace or charge batteries in a hazardous atmosphere. Contact sparking may occur while installing or removing batteries and cause an explosion or fire.
Turn radio off before removing or installing a battery or accessory. Use of a radio that is not intrinsically safe in a hazardous atmosphere could result in serious injury or death. Do not replace or change accessories in a hazardous atmosphere. Contact sparking may occur while installing or removing accessories and cause an explosion or fire.
Keep the connector cover in place when accessories are not used. Items not considered as repairs are those in which an action is performed on a unit which does not require the outer casing of the unit to be opened in a manner which exposes the internal electrical circuits of the unit. Relabeling The repair facility shall have a method by which the replacement of FMRC Approval labels are controlled to ensure that any relabeling is limited to units that were originally shipped from the Manufacturer with an FM Approval label in place.
FMRC Approval labels shall not be stocked by the repair facility. An FMRC Approval label shall be ordered from the original manufacturer as needed to repair a specific unit. Replacement labels may be obtained and applied by the repair facility providing satisfactory evidence that the unit being relabeled was originally an FMRC Approved unit.
Verification may include, but is not limited to: a unit with a damaged Approval label, a unit with a defective housing displaying an Approval label, or a customer invoice indicating the serial number of the unit and purchase of an FMRC Approved model.
Do Not Substitute Options or Accessories The communications equipment package that Motorola submits to FMRC for testing and approval is tested as a system that consists of the communications unit itself and the battery, antenna and other options or accessories that make up the rest of the package to be approved.
This approved package must be strictly observed and there must be no substitution of items, even if the substitute you wanted to consider appears as an approved accessory elsewhere in the Guide for some other communications equipment unit. That guide, and the Approval Standard Class Number document, can be ordered from the following address.
Locate the battery latch on the bottom of the radio. Push the battery latch toward the front of the radio and hold it in the open position as shown in Figure Figure Push in on tab of belt clip with small flat-bladed screwdriver, and at the same time slide belt clip toward top of radio Figure CAUTION Lift the chassis approximately half way out of the front cover, because you must disconnect the flex cable before completely removing the chassis.
It outlines what you need to program them. If you would like to learn how to program these radios, we will link to a few guides at the bottom of this page. You might want to join this dedicated group on Facebook. The portable radio is programmed via the back of the radio. If they come up 1,2,1,2,1,2,1, Expand the radio to 16 channels, Alternate Method 2 Depending on which firmware is in your radio, this may or may not work see Note above.
Open the GP MDF in your Hex editor and make a Checksum of the whole file. You will need this later, so write it down. For RSS version 5. Search for your model number in the file, you probably will come accross more than one entry so you can either change them all or change them one by one until it works.
P If you look at this model entry, the third byte after the model number offset 0x87A is a This is the hex representation for the number of channels in the radio, in this case 16ch. Most of the time you will see a 0x02 or 0x08 in this position for 2 or 8 channel radios respectively.
Try changing the field to 0x10 to make a 16 channel radio and see what happens. Also note the 06 at offset 0x, this is the bandsplit for this model number and corresponds with the bandsplit entry in the table at the top of the.
If the checksums do not match you will get an error message. To find out if you picked the correct model number to edit, save the. Try adding channels with the Mode Utility and see what happens.
If you would like to program any GP radio with the codeplug information previously got from another GP serial number, model, freq. Run gp Press F8 and program any target GP Model number, serial and features will be copied into it. If you want to disable frequency checking for entering out of band frequencies in RSS, try doing the following modifications: Search for 77 10 around location 3E80 and replace with 90 90 Search for 77 03 around location 3E8D and replace with 90 90 One disables frequency checking on tx, the other on rx.
Note that the locations will vary depending on the version of RSS. Out of band for 5-tone radios This seems to work on 5-tone version 2 RSS. Program your out of band frequency into either the TX or RX field, then use [shift]-F2 to leave the field. Another thing to try is using the shift key to enter the frequencies into the field remembering to release it for the decimal point, ie. If this doesn't work, then try the method below.
You will have to make modifications to the gpt. You should probably find an entry at addresses h, replace with FE1Eh. You should probably find an entry at addresses 06D0h, replace with FE1Eh.
You should probably find an entry at addresses h, replace with C04Ah. This should be all that is required. For a VHF version, the process is similar. All you have to do is convert the edge of the bandsplit you are looking for from decimal to hex using Hex Workshop'd Base Converter make sure the byte order is "Intel" and search in the file for it. Have a look at the manual Motorola Gp z07 0 Manual online for free.
E-mail address. Remember login. Login or create new account. Add to Favourites. View all the pages. Add page 1 to Favourites. Enable zoom. Add page 2 to Favourites.
0コメント