Let me know if that works.. Thanks, Jim R. Control filter pump, heater, solar, spa, and 7 auxiliary circuits. Remotes are designed to be installed above water level in the spa tile line, decking, or anywhere outdoors in conjunction with any model AquaLink RS. Each SpaLink is packaged with a matching flush mount frame and is available in multiple. It is typically installed at the tile-line of the spa wall, or in the deck within arm's reach of the spa.
It can be used with a gunite spa, acrylic spa, or hot-tub. I found the lables for mine inside the control box.
Previous owner or installer must have put them there. It is available with different length cords, go to the Jandy website or just search online. I remember seeing a ' version. I've installed hundreds of these, so I was pretty sure this was what you guys were looking for I just needed to verify cord lengths if I was going to try and help.
There are several different lengths, and they come with different pricing, so that is an important part of the puzzle. If either of you would like me to go to the supply house and check on these for you, I would be happy to do it. Just PM me your information so that I have it and can print it out.
Jayl New member. Feb 3, 2. I have same switch but to a Aqualink RS4. My Spa switch out at the hot tub is not working and the center RED light remains lit. I have done resets, and cleared memory, reprogramed.. The spa works fine from the control in the house. Any suggestions? Apr 19, 1. Hello all: I have this same problem however I don't need to replace the wire. I only want to replace a switch.
Is this possible? Thanks Fond. LifeTime Supporter. Nov 5, 2, We are getting ready to do the same replacement here. Shopping for the switch itself now, in white, 4 button. Follow up to replacing Spa Side Switch. Thanks to all those who gave advice here. All went well. The unit popped out with a screwdriver easily. After that it was all easy-peasy. I have same switch and red light in center remains lit, even with system off. Also none if the buttons work. However, Spa works fine from the outside service control panel and also from in the house.
Just beware, once that spa side switch starts to fail, any one of those buttons might activate itself at any time. That was why we had the weird light show on and off in the middle of the night. I suggest that you follow the directions for de-activating the spa side switch in the instruction manual.
That way it will still work with the inside and outside box, but no random actions that might harm equipment. You must log in or register to reply here. Thread Status. Hello , This is an inactive thread. Any new postings here are unlikely to be seen or responded to by other members.
You will get much more visibility by Starting A New Thread. Similar threads N. Replace Jandy Spa Side Switch with different brand switch? Aug 25, Mt Juliet, Tn. I am getting some work done on the flagstone on my spa and I need to have the spa empty for 2 days. I can drain the spa but I would like to run the pool pump during this time. In the photo there is a yellow circle around the jandy actuator.
If I could rotate that valve degrees it would stop any water from going to the spa. I will also turn the blue circle to off so suction wont happen from the spa. My question is, if I unscrew the actuator, can I put the handle back on without the actuator and manually rotate it to any position or will I have to open the valve housing up?
TFP Expert. Bronze Supporter. You can. Push down on the locking knob not the handle. This will disengage the gear train and allow the handle, and thus the valve diverter, to be moved to any position. To return the actuator to automatic position, pull up on the handle while turning it clockwise or counterclockwise until you feel the shaft slide up into the gear train.
Turn the locking knob down clockwise until snug. Put toggle switch back to the original position. You may also just be able to change the toggle switch to the opposite setting and it will turn the valve to the other setting.
Rossterman Well-known member. Jun 5, Martinez, CA. You can simply move the valve using the toggle switch if the limits provide full movement. When it is in the correct position, return the toggle to the middle position. Leave it there until you work is done than put toggle back in original position so valve will return to normal running position.
0コメント